
Line Board Versus Fog Board for PDR Repairs
, autor Admin, 8 min czytania

, autor Admin, 8 min czytania
Compare line board versus fog board for PDR repairs. Learn where each reflection tool excels, how to read damage and choose the right finish quickly.
A dent can look finished under one reflection and still show a low, a tight crown or a wavy texture when the vehicle leaves the bay. That is why the line board versus fog board decision matters. Both tools help you read panel movement during paintless dent repair, but they show different information. Choosing the right one at the right stage gives you better control of the metal and reduces unnecessary pushing and knocking down.
Neither board replaces sound PDR technique, suitable access or a stable light source. They are visual reference tools. Used properly, they make the panel’s condition easier to see before, during and after a repair.
A line board uses defined stripes, usually contrasting black and white lines, to create a sharp reflection across the damaged area. As the panel moves in or out, those lines bend, spread, tighten or break. This gives the technician an immediate view of the dent’s shape, its edges and the exact effect of each push.
A fog board produces a softer reflection, often using a smooth fade from dark to light rather than crisp lines. Instead of focusing your eye on individual line movement, it helps you see broad changes in the panel surface. The result is particularly useful for reading shallow lows, crowns, stretched metal and finish quality across a wider area.
Put simply, the line board is usually the more precise pointer. The fog board is the broader surface reader. Most technicians get the best results by treating them as complementary tools rather than alternatives that must be chosen once and used for every repair.
Board designs vary between manufacturers. Some PDR lights have interchangeable line and fog panels, while others use adjustable lenses, covers or printed boards. The principle stays the same: sharp contrast reveals detail; softer contrast reveals flow.
Use a line board when you need to locate and control a specific point in the damage. The clear stripe pattern makes it easier to find the deepest part of a conventional door ding, establish the edge of a crease or judge whether a tool tip is landing where intended.
During a push repair, line movement gives fast feedback. If the stripes rise cleanly at the point of pressure, you know the metal is moving. If they distort too quickly or form a tight peak, you can stop before creating a high spot. This is valuable when working through restricted access with a rod or pick, where a few millimetres of tool movement can change the result.
Line boards are also useful for precision finishing on relatively direct panels. On a door skin, wing or bonnet with good access, the narrow lines can expose small remaining lows that might be missed under a broad reflection. For technicians building consistency, the pattern offers a clear visual language: a smooth, even line usually indicates a smooth, even panel.
There is a trade-off. Strong lines can make a panel appear busier than it is. On a large, soft dent or a panel with complex factory body lines, the reflection may be difficult to interpret. A technician can become too focused on correcting every tiny bend in a stripe, even where the overall panel flow is already acceptable. This can lead to overworking the metal.
A line board is often the practical first choice for small to medium door dents, sharp impacts, hail dents requiring point-by-point control, and repairs where you are tracing a defined body line. It is equally useful while learning how a push or tap affects the surface because the feedback is immediate and easy to compare from one move to the next.
For very tight damage, adjust the board or light position before increasing tool pressure. A close, sharply focused reflection may reveal detail, but it can also exaggerate it. Move the light, change the angle and confirm what you are seeing before chasing a mark that may be only a reflection artefact.
Fog boards come into their own when the repair is no longer about finding one point. They help you assess whether the panel has returned to its natural, even shape. The soft gradient is more forgiving to read and often better at revealing broad displacement, subtle crowns and texture around the original impact area.
This makes a fog board especially effective on large shallow dents, oil-canning panels and finish work after glue pulling. Following a series of pulls, for example, a striped board may show several small variations without making it obvious whether the panel is generally high, low or flowing correctly. A fog reflection shows the overall direction of the panel more clearly.
It is also helpful around wide factory curves. Roof rails, rear quarters, bonnets and modern vehicle doors often have gentle contours that make straight lines appear distorted even when the panel is sound. A soft fade gives you a more natural reference for the vehicle’s shape.
The limitation is that fog boards do not always reveal a pinpoint imperfection early enough. A small, sharp low can disappear into the gradient, especially on light-coloured paint or a reflective panel. If you are trying to identify a precise tool location, switch back to lines. Fog is excellent for judging flow; it is not always the fastest way to find a tiny centre low.
Choose a fog board when checking a broad repair after the main metal movement is complete, blending a shallow low into surrounding panel shape, or reducing a crown without creating a hard transition. It is particularly useful for final inspection before releasing a vehicle, because it encourages you to look at the repair as a complete surface rather than as a collection of individual marks.
Technicians who perform high-volume retail work often benefit from keeping fog available at the finishing stage. It can prevent the common mistake of producing a technically flat centre with a visible halo around it. A repair is only convincing when the light moves naturally across the entire affected area.
A productive PDR workflow rarely stays with one reflection pattern from start to finish. Start by assessing the damage under a line board if you need to map the centre, edges and any sharp features. Make controlled pushes or glue pulls, checking the reaction of the lines after each adjustment. As the dent becomes shallower, use a fog board to evaluate the wider panel and identify crowns or uneven tension.
Then return to lines when a small low needs finishing, and use fog again for the final flow check. This process is not slower than working with one board throughout. It usually saves time because you are using the clearest visual information for each decision.
The vehicle and paint condition matter too. Dark paint often gives strong reflections and can make line detail easy to read. White, silver and heavily metallic finishes may require more careful board placement, a different light angle or a softer fog pattern to show the same defect. Dirt, poor lighting and reflections from workshop doors can mislead your eye, so clean the panel and control the working environment before judging the finish.
A high-quality line or fog board cannot compensate for poor positioning. Set the reflection so it crosses the damage at an angle that makes the panel movement visible. If the board is too far away, the detail may be too small to read. If it is too close, the pattern can become exaggerated and difficult to interpret.
Move your viewing position as well as the board. Looking straight at the damage may hide a crown that becomes obvious from slightly to one side. On body lines, inspect from both directions. A repair that reads cleanly across the line may still show distortion along it.
Keep the board or light stable while making a final judgement. If you are constantly changing the angle, it is easy to confuse changing reflections with actual panel movement. Consistent positioning makes your before-and-after reading more reliable, particularly when several technicians share a bay.
For a professional setup, look for a PDR lighting system that lets you change reflection styles without rebuilding your work area. Adjustable brightness, stable mounting and a board size suited to your usual repairs matter more than decorative features. Mobile technicians may prefer a compact, easily positioned unit, while a fixed workshop bay can support a larger board for quarters, roofs and bonnets.
If you are buying your first reflection equipment, a line board is often the more direct training tool. It helps connect tool movement with metal movement. Add fog capability as soon as possible if you regularly handle larger dents or want a cleaner final inspection process. The extra reading option can protect repair quality and reduce the time spent correcting avoidable highs.
TrAuto’s approach is straightforward: choose equipment that supports accurate repairs, fits your daily workload and can be replaced or exchanged without unnecessary downtime. A good reflection setup should help you make confident decisions, not add another variable to the job.
Before handing the vehicle back, take one quiet minute to inspect the panel under both a defined line and a soft fog reflection. If the detail is clean and the panel flow looks natural, you have a finish that will stand up outside the workshop as well as under your PDR light.